Tag Archives: orchid

The Orchid V2 RTA Clone $11.08!

After a much needed personal leave from the site I am back! And what a great time it is to be reviewing the new vaping gear. Lots has changed in my absence and I plan on playing a little catch-up through my articles, but this here is the newest, latest and greatest. Today the highly anticipated V2 of the Orchid atomizer clone popped up for a ridiculously low price. At $11.08 it is cheaper than just about any other rebuildable tank atomizer available and after using the Tobeco V1 Orchid for a couple weeks, I would highly endorse this RTA. Although the design of this atomizer is not perfect, the price and features really make this a great addition to any collection. Here is my review/preview of the Orchid clone. 

4 Channels! 4 posts! 4 pieces!

4 Channels! 4 posts! 4 pieces!

Many Vapers out there would relate this atomizer to the Kayfun or Fogger v4 and they wouldn’t be wrong. I have toiled around with my own Orchid and found many parts to be interchangeable with my army of Kayfuns. The chimney section on this atomizer is wider than the Kayfun’s and is not interchangeable. This puts a bit of a limit on the amount of parts that can be swapped. Personally I don’t care for the plastic tank or top-heavy cap, which lead me to explore every possible combination of tank sections and top caps that would be compatible. Once again I became slightly frustrated with the chimney which I found to be too short to noticeably increase the tank capacity. The sellers claim the capacity is 2.5ml – 3.0ml, but I am finding it to be closer to 2ml. I finally settled on using 1 Kayfun Nano steel tank section paired with a regular Kayfun clear tank and steel band. I chose my flat-cap that came with my Kayfun Lite +v2 to top it all off. 

My personal pocket rocket. Pictured on a 4nine clone in 18350 mode.

My personal pocket rocket. Pictured on a 4nine clone in 18350 mode. This is the maximum capacity the chimney would allow

The new V2 of the Orchid clone features a bottom filling port for those Vapers that hate removing the cap. I have been using the top fill and flip method without many issues. Besides the fill port change, the Orchid V2 clone is the same as the V1. The deck on this atomizer does use allen screws, I would have preferred a Phillips option, but I can live with it. I use my Orchid with a dual coil at .7ohms and I have not had a single wicking or gurgling issue. I use considerably less cotton in my builds, and I would say they are very similar to a Fogger v4 with the cotton running half way down the vertical juice channel. The draw is very airy and the vape might even satisfy some cloud chasers out there. Since I have been using this with the purple 18350 batteries I usually swap the battery each time I fill.  

The new fill port will make some people happy, others have been using the top fill kayfun cap from Fasttech.

The new fill port will make some people happy, others have been using the top fill Kayfun cap from Fasttech.

I paid almost double for my Tobeco Orchid and am very happy with it. If you are looking for a Kayfun with larger clouds you really can’t go wrong at this price. I wish there was a middle ground between the Fogger v4 and the Orchid, just like a Kayfun with the base from this atomizer. 

Here is what the site says about it:

  • Compatible with 510 drip tip (drip tip sold separately)
  • Quad-pole for dual coil build
  • 4 wick channels
  • 2 air holes
  • 510 connection (brass contact, adjustable)
  • Laser engravings on the chimney
  • Bottom screw-refill hole

Get yours here: http://www.fasttech.com/products/1411/10009514/1850901-orchid-v2-styled-rebuildable-tank-atomizer-2-5-3

Stay tuned with the site, I am planning on adding plenty of new content in the near future!

Advertisements